Extreme Coatings donates to 11th Annual Oilman’s Hill Country Ride

Extreme Coatings is helping to sponsor the 11th Annual Oilman’s Hill Country Ride, April 16, 17 & 18, 2015. This charity ride raises money to support men and women of the US Armed Forces, including organizations such as Wounded Warriors.

Read more here: http://www.oilmanshillcountryride.com/index.html

Large hydraulic shafts are chrome plated so that a seal ring can slide easily over this surface during operation

Large hydraulic shafts (fork lifts, back hoes, dump trucks, etc.) are chrome plated so that a seal ring can slide easily over this surface during operation. Over time chrome will wear or corrode and this leads to breakdown of the packing seal. The result – loss of hydraulic pressure, contaminated fluids and the need to re-chrome or replace the shaft. Tungsten carbide coating will replace chrome in this application and last many times longer. The surface finish for polished tungsten carbide is 2-4 Ra with an Rz of 12-15. This smooth surface ensures packing seals will also last a long time. The higher corrosion resistance carbide coating is perfect for areas prone to corrosion pitting – ocean work zones, chemical plants, etc.

. Pelletizing dies made from tools steel are used in under water polymer pelletizers.

Pelletizing dies made from tools steel such as D2 (12% chromium) and H-13 ( 5% chromium) are used in under water polymer pelletizers. These steels provide abrasion resistance and withstand general wear from a cutting knife sliding over the surface at high speeds. A tungsten carbide finished coating layer of just .010” (surface ground and polished) can provide three times the wear resistance compared to these tool steels. In some cases it is possible to recoat a worn die or simply grind away the wear groove and continue using a tungsten carbide coated surface.

Extreme Coatings uses experience coating injection molding feed screws to extend the life of gas and oil drilling equipment

For the past 15 years, Extreme Coatings, Inc. has had tremendous success using thermal spray carbide coatings to significantly increase the life of the feed screws used in plastic injection molding and extrusion equipment.  The same technology and expertise is now being used on downhole mud motor rotors for the oil and gas drilling industry.

For Extreme Coatings, the move was a natural one.  The geometry and actions of mud rotors are very similar to those of feed screws, so existing technology and working methods were directly applicable.

Mud motors are a type of displacement pump used in drilling for gas and oil.  The most expensive part to replace is the power section, consisting of a rotor and a stator.   Historically, stainless steel rotors have been chrome plated. When the drilling fluid, or mud, is fouled, the chrome plating can rapidly wear away in places and build up in others.  When that occurs, the incorrect fit can cause a loss of power to the drill and eventual motor failure. With increased exploration into corrosive environments such as shale formations, the demand for more corrosion- and wear-resistant coatings has grown.

Through new coating development like their CPR (Chrome Plating Replacement) coating and refined polishing techniques, Extreme Coatings is not only repairing the mud rotors, they are making them run better.  Extreme Coatings strips away worn chrome plating and replace it with a more corrosion resistant high velocity oxy-fuel (HVOF) thermal spray coating. The tungsten carbide used in these coatings is harder than chrome, and the method of application and polishing results in a high finish that reduces friction. This can increase the life of a rotor by six to ten times.

Carbide Coatings for Halogen-Free Flame Retardant Applications

This is a shout out about our carbide coatings for Halogen-free flame retardant applications. These are nasty corrosive materials that are growing in usage in the electronics industry. Processors that are used to equipment life of 24-30 months for PM tool steel are totally surprised when they change materials to a product with zero halogen in it. They can see their feedscrews reduced to broomsticks in a matter of 3-4 weeks!

The issue is corrosion AND abrasion at the same time. Corrosion resistant steels form an oxide layer that protects the surface from continuous corrosion. With an abradant (glass fiber) in the mix this oxide layer is constantly removed and the result is a loss of material at a rapid rate.

Our tungsten carbide coatings are inert and the finished coating layer hard and has very low porosity. Once a feedscrew is coated it will last at least as long as the original PM steel screws in this halogen free material. I will post a link here soon with a copy of an article from the German press about this problem.